Mentor Graphics Launches New T3Ster DynTIM Tester to Deliver Unrivaled Thermal Interface Material (T
Mentor Graphics Launches New T3Ster DynTIM Tester to Deliver Unrivaled Thermal Interface Material (TIM) Measurement Methodology
WILSONVILLE, Ore.--(BUSINESS WIRE)-- Mentor Graphics Corporation (NAS: MENT) today announced the new T3Ster® DynTIM™ tester, the industry's cutting-edge method of measuring thermal characteristics of thermal interface materials (TIM). Thermal resistance testing of interface layers within electronics products is critical for product performance, but the characterization of these thin, high-thermal conductivity materials under realistic conditions for their application is extremely challenging using current methods. The Mentor Graphics® DynTIM tester meets the needs of manufacturers today with the ability to control and vary the sample thickness of materials being tested, yielding very accurate results. Engineers can perform more accurate thermal analysis when using the Mentor® T3Ster DynTIM with the Mentor FloTHERM® and/or FloEFD™ CFD solutions.
Testing systems using today's current methods (ASTM D5470 Standard Test Method for Thermal Transmission Properties of Thin Thermally Conductive Solid Electrical Insulation Materials and ASTM D5470-06 Standard Test Method of Thermal Transmission Properties of Thermally Conductive Electrical Insulation Materials) do not allow for lower pressure measurements. This causes less than accurate results, nor can the test results be replicated without a 10-20% repeatability error (based on conductivity data reports from various vendors). The Mentor Graphics DynTIM tester, combined with the company's T3Ster test product, provides the industry's most accurate method of measuring thermal resistance of TIMs under conditions close to real life applications on a variety of materials at different pre-set thickness levels, such as greases, pastes, phase-changing materials and even specially prepared metallic samples. On average, the DynTIM tester provides TIM measurement accuracy by ±5% with the highest repeatability results, which the industry is currently lacking since most ASTM-based tests are conducted using in-house test systems.
There are two reasons for the superior results provided by Mentor Graphics. First, DynTIM users can test a large number of different TIMs to create a short-list of the best performing materials as possible candidates for the application. Secondly, after the measurement of the material properties and narrowed selection of the TIMs, the T3Ster tester can be used to test these materials in-situ, in their target environment, for the best possible design decision. This total solution is ideal for semiconductor, consumer electronics and TIM manufacturers where controlled manufacturing of materials performance is critical.
"We have been using the T3Ster DynTIM tester and love its speed and ease of use. It uses a very accurate method for characterizing thermal interface materials because it automatically varies the thickness of the sample," said Dr. Thomas Zahner, quality manager at Osram Opto Semiconductors GmbH. "DynTIM helps us to develop LED lighting modules with excellent thermal performance and to ensure their thermal reliability over the whole product lifetime."
"With our deep understanding of our customers' thermal challenges, we are proud to deliver the industry's most accurate TIM testing solution," said Erich Buergel, general manager of the Mentor Graphics Mechanical Analysis Division. "We are committed to our thermal characterization customers and we will continue developing innovative solutions that help them deliver better end-products with greater efficiency to compete in today's global economy."
For more information on the Mentor Graphics Mechanical Analysis Division products, go to the website: http://www.mentor.com/products/mechanical/products/dyntim/
About Mentor Graphics
Mentor Graphics Corporation is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world's most successful electronic, semiconductor and systems companies. Established in 1981, the company reported revenues in the last fiscal year of about $1,015 million. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com.
(Mentor Graphics, Mentor, T3Ster and FloTHERM are registered trademarks and DynTIM and FloEFD are trademarks of Mentor Graphics Corporation. All other company or product names are the registered trademarks or trademarks of their respective owners.)
KEYWORDS: United States North America Oregon
The article Mentor Graphics Launches New T3Ster DynTIM Tester to Deliver Unrivaled Thermal Interface Material (TIM) Measurement Methodology originally appeared on Fool.com.Try any of our Foolish newsletter services free for 30 days. We Fools may not all hold the same opinions, but we all believe that considering a diverse range of insights makes us better investors. The Motley Fool has a disclosure policy.
Copyright © 1995 - 2012 The Motley Fool, LLC. All rights reserved. The Motley Fool has a disclosure policy.