Why 3D Systems Corporation and Arcam AB Could Be Big Winners Because of This New U.K. Development

Before you go, we thought you'd like these...
Before you go close icon

Cambridge University spin-off Metalysis has developed a process to cut the cost of titanium powder by up to 75%, and reportedly is in talks with commercial partners to build a $500 million plant to churn out low-cost titanium powder. Titanium is incredibly lightweight, yet also strong and highly corrosion resistant. These properties make it a top materials choice for aerospace applications, medical implants, and other specialty uses, yet it isn't used much in mass manufacturing because it's very pricey. 

If Metalysis' process works as well as is being reported, companies that make 3-D printers that can print in titanium could be big winners. Of the five major 3-D printing companies that trade on U.S. exchanges, only industry leader 3D Systems and Sweden-based Arcam make systems with titanium and/or titanium alloy capabilities; ExOne has reportedly been working on developing this capability, while Stratasys and voxeljet don't offer any systems that can print in metals. 

The 3-D printing titanium players: 3D Systems and Arcam
The reason this development could turbocharge the already fast-growing 3-D printing sector is that this lower-cost titanium will only be available in powder form: 3-D printing uses powder as a raw material, while conventional "subtractive" manufacturing uses solid materials. 

It's very likely that some companies that now use other metals to produce certain components will consider using titanium if it's more competitively priced. Higher-end automakers and others will likely start using titanium for select parts that are now made from aluminum or steel.

The titanium powder produced by Metalysis' process is high-grade, but not quite aerospace-grade. So, at this point, manufacturers that currently produce titanium aerospace components using conventional manufacturing won't have the extra cost-savings incentive to switch to 3-D printing.

3D Systems only recently acquired metals printing capabilities when it bought Phenix Systems last summer. Its printers use laser sintering technology, which is the most commonly used metals 3-D printing technology. 3D Systems machines can print in stainless steel, tool steels, aluminum, titanium, precious metals, among other metals.  There are a few privately held companies that also make 3-D printers that use laser sintering technology; most notable is Germany-based EOS.

3D Systems launched three rebranded Phenix Systems' printers at last year's EuroMold: ProX 100, ProX 200, and ProX 300, and is already competing for key new business with its new metal printer lineup. General Electric has reportedly been testing printers from 3D Systems to see if the company will be part of its capacity ramp-up necessary to produce thousands of fuel nozzles for its new Leap jet-engine.

Arcam has considerable experience making 3-D printers that have titanium capabilities, as it's been solely involved in the industrial metals end of the 3-D printing sector since it was founded in 1997 (though the company's roots and technology go back further). Arcam's 3-D printers use its proprietary electron beam melting, or EBM, technology, and can print in titanium, several titanium alloys, and a cobalt-chrome alloy. The company has been exclusively focused on two markets: aerospace and orthopedic implant. 

Arcam's systems are relatively small, so they'd currently not be able to produce larger components in titanium. However, surely the company could develop and make larger systems using its EBM technology if demand warranted it.

Titanium economics, and titanium making 101
Metalysis' development could turn the metals markets topsy-turvy, as demand for titanium should rise at the expense of the aluminum and steel markets.

Titanium powder sold for $200 to $400 per kilogram, as of December. Shaving up to 75% off its cost would make titanium much more competitively priced with aluminum powders, which were selling for about $30-$50 per kilogram, and almost as cheap as specialty steels. Given the cost factor, it's not surprising only about 140,000 tons of titanium was produced and consumed globally in 2012, compared with 1.5 billion tons of steel and 48 million tons of aluminum, according to the Financial Times. 

Titanium is now produced using the Knoll process, which is an 80-year-old technology that's very inefficient. The four-step process uses a lot of energy and only produces small quantities of titanium. By contrast, Metalysis' technology involves just one step. It uses electrolysis to convert rutile sand, a naturally occurring titanium ore present in beach sands, directly into powdered titanium.

This is here-and-now technology, not tech that's still in the R&D stage. Metalysis has long collaborated with Sheffield University's Mercury Center, which specializes in metal powder-based manufacturing. Engineers at the Center have successfully 3-D printed various components using titanium produced by Metalysis' process. This includes what they believe to be the world's first 3D-printed titanium car component, according to an article in TCT Magazine

In what appears good news for Arcam, Prof. Iain Todd, director of the center, was quoted by TCT as saying: "We've been operating since 2007, which is when we got our first Arcam system. We're more focused around electron beams than lasers and we do a lot of work mainly with industrial partners, so our projects are supported by the European Regional Development Fund."

Foolish final thoughts
There are several reasons why investors might want to keep their eyes on Metalysis' progress in building a titanium powders production plant based on its technology. First, companies that make 3-D printers that can print in titanium, which include Arcam and 3D Systems, would almost surely see demand for their systems increase. Second, there could be some significant investment opportunities in the metals market. Lastly, Metalysis could make for a potentially attractive IPO. 

Don't miss our top stock for 2014
There's a huge difference between a good stock and a stock that can make you rich. The Motley Fool's chief investment officer has selected his No. 1 stock for 2014, and it's one of those stocks that could make you rich. You can find out which stock it is in the special free report "The Motley Fool's Top Stock for 2014." Just click here to access the report and find out the name of this under-the-radar company.


The article Why 3D Systems Corporation and Arcam AB Could Be Big Winners Because of This New U.K. Development originally appeared on Fool.com.

Beth McKenna has no position in any stocks mentioned. The Motley Fool recommends and owns shares of 3D Systems. Try any of our Foolish newsletter services free for 30 days. We Fools don't all hold the same opinions, but we all believe that considering a diverse range of insights makes us better investors. The Motley Fool has a disclosure policy.

Copyright © 1995 - 2014 The Motley Fool, LLC. All rights reserved. The Motley Fool has a disclosure policy.

Read Full Story

People are Reading